Author - Gary Yeung

31Aug

Remote Control

Display Screen Display screen shows the time setting, charging status, and error codes by using numbers, letters, or graphic. Buttons 2. "Home" Auto Charging Press "HOME" button and the RolliBot BL618 will go back to its charging station to automatically charge. Press "HOME" button again or the "On/Off" button and RolliBot BL618 will stop and go into standby mode. 3. "PLAN" Schedule Button Press "PLAN" button to set up scheduled cleaning operation. Click to see schedule cleaning setup. 4. "On/Off" Clean Button A. Press this button twice...

Read more...
12Aug

Battery Charging

Battery Charging A. Charging Station Placement Place charging station against the wall and remove obstacles about 1 meter (3.3 ft) at two sides and about 2 meters (6.6 ft) in front of the station, as show in figure below. Charging Station Placement - 6.6 ft clearance in front and 3.3 ft clearance to the sides   Two ways to charge your RolliBot: 1. Plug the power adapter directly into the RolliBot. See Figure A below. Plug adapter into directly into RolliBot. 2. Setup charging station and press the...

Read more...
12Aug

Adding Mopping Attachment

Adding the Mopping attachment to RolliBot Adding Mopping Attachment to RolliBot Attach wet tissue or micro-fiber cloth to mopping holder Attach mopping holder to the bottom of RolliBot. Make sure to align the bolts and firmly press the mopping attachments into the slots on the bottom of RolliBot. If wet tissue is bigger than mopping holder, please trim wet tissue to mop holder size. Make sure the wet tissue does not rub or cover the robot wheels Be sure to turn off the UV Sterilization...

Read more...
12Aug

Cleaning side brushes

Clean the side brush when it gets dirty and replace it if it is damaged. Max life span for side brush is 12 months. Note: Before replacing side brushes, check for "L" and "R" mark on side brush and match with "L" and "R" mark on bottom base of the robot.

Read more...
12Aug

Cleaning Dust Bin and Filters

Empty and clean dust bin after each use. Follow the steps shown below: Cleaning dust bin and filters. NOTE: Wash HEPA filter after used for 15-30 days. Max life span for HEPA and primary filter is 24 months. Reinstall the HEPA and primary filter after they are fully dry. HEPA and primary filter could be replaced if needed. Do not dry the filters under direct sunlight.

Read more...
12Aug

Error Codes for Motors

Troubleshooting - Error Codes for Motor Error Code Cause Solution L01x Fan overloaded Check if fan is covered and clean dust bin and dust filters L0x1 Left wheel overloaded Check if it is jammed or tangled by obstacle. L0x2 Right wheel overloaded Check if it is jammed or tangled by obstacle. L0x3 Left and right wheel overloaded Check if it is jammed or tangled by obstacle. L0x4 Left side brush overloaded Check if it is jammed or tangled by obstacle. L0x5 Left wheel and left side brush overloaded Check if it is jammed or tangled by obstacle. L0x6 Right wheel and left side...

Read more...
12Aug

Error Code for Sensors

Troubleshooting - Error Code for Sensors RolliBot Displaying Error Code: AUBN (dust bin removed) Error Code Cause Solution AUBF Suction passage blocked Clean suction passage AUBN Dust bin not installed correctly or dust bin removed. Remove and replace the dust bin inside the robot. E1xx Left collision switch fault Check front bumper. E2xx Right collision switch fault Check front bumper. E3xx Left and right collision switch fault Check front bumper. E4xx Left wheel off the ground Place robot on ground. E5xx Left wheel off the ground, left collision switch fault Place robot on ground and check front bumper. E6xx Left wheel off the ground, right collision switch...

Read more...
Join The Waiting List We will inform you when the product arrives in stock. Just leave your valid email address below.
Email We won't share your address with anybody else.